Music Mission FAQ

Only one mission can run at a time, user can go from one mission to the other at any given time.  While all mission parameters will be kept, the RAVENNA/AES67 streams will need to be reconnected or Re-UNITE.

The Music Mission is free of change and is included in the firmware 1.2.2 and above. Any Anubis owner can run the Music Mission and the Monitor Mission.

The Mute button will not appear directly on the Anubis Music Mission Mixer but can be accessed in two different ways.

1. Single tap the Strip channel will open the Horizontal Fader in which a Mute button will be available.

2. The channel Mute can at any given time be accessed from the channel menu located at the bottom of the channel by tapping on it.

Once enabling the Mute, it will replace the Solo button on the main Mixer view, and can be un-muted at any given time.

Ex-Factory the Music Mission is launched in default mode with simplified view and limited features.
To access all of the Music Mission feature set enable the Expert Mode from the Anubis Settings under Music.

The AES67 Stream feature available under the Settings>Audio Inputs allows the users to create a stream up to 48 input strip channels, those can thus be connected to the Direct Outputs of the DAW channels Mixer and will appear in the Anubis Mixer for Mixing in the Anubis itself.

The Music Mission mixer does not support DSD, but allows users to record the direct PreAmps in DSD, monitoring such outside the ANUBIS. 
For proper DSD Monitoring it is recommended to run the Monitor Mission.

With the Anubis Music Mission the recordings of the Anubis inputs channels into your DAW or application by default are non-destructive (no Anubis effect will be applied). The feasibility to record Post- FX signal (Post-Effect) is avialable. This one includes the EQ and Dynamics plugins. Record the Physical Input Direct signal (Pre-Effects) and the Post-FX single independently or simultaneously. Support for Unite Post-FX is requiring the VAD 3.2.1 and higher or MAD 2.2.0 and higher version along with an Anubis Firmware 1.4.2 and above.

In the UNITE dialog Post-FX Inputs should be checked

Users can connect the Post -FX channels via ANEMAN.

The Reverb, the Parallel Dynamics and Sends are not in the Strip signal Effect path. In order to record those, it is recommended to record the Bus returns.

To record Bus Returns (Reverd, Parallel Dynamics and other applied Effects) the Cues can be used. Procedure below.

• Enable Expert Mode (Settings>Music)

• In the Setting>Mixer under CUE-4 and CUE-5  unlink the Pan's for those two cues.

• Exit your Settings

• Enter CUE-4 and Pan Anubis Input 1 hard left and Anubis Input 2 hard right left

• Enter CUE-5 and Pan Anubis Input 3 hard left and Anubis Input 4 hard right left
  Note: It is preferred to leave all levels to 0dB nominal.

• In the MAD or VAD panel Re-UNITE your Anubis and make sure the "Bus Returns" is checked

  

• Record in your DAW the CUE-4 (Anubis inputs 1-2) and CUE-5 (Anubis inputs 3-4)
  Those will be recorded Post FX.

No. Split Channel is currently available only in the Monitor Mission. This feature duplicates an input into two channels with independent gain settings, for example to set separate gains for FOH and monitoring, or to record a backup copy at a lower gain level for peak safety.

56 x EQ of 4 bands each are available (as of Firmware 1.4.6 and above)
64 x Dynamics are available within a single Anubis running the Music Mission
4 to 20 Merging+Deesser depending of EQ and Dynamics resources available 
1 x Merging+Reverb
1 x Eventide Blackhole

You can apply EQ on the Dynamics or Reverb. From the Mixer Menu enter the Parallel Dynamics or Reverb to apply EQ on those.

Yes the Reverb Spatialization will be in stereo.

The sidechain option is only available when the Dynamics module is enabled on both channels involved:

• the source channel, whose signal triggers the processing (the key/sidechain input)
• the destination channel, where the dynamics processing (compressor, gate, etc.) is applied

If the Dynamics module is bypassed or turned off on either of these channels, the sidechain is automatically disabled. To use it, enable the Dynamics module on both the source and destination channels, then select the source channel as the sidechain input.

As of firmware v1.2.2 build 47903 and above two Anubis can peer the same input module. Meaning that the AD1 of the Hapi could be peered by the Anubis-A and the Anubis-B at the same time. 

But its important to know that an output module cannot be peered by two different Anubis. So the Anubis- A cannot peer the Hapi Headphones while the Anubis -B also peers the same Hapi Headphones, in this case the last one peering the output module will take over this one.